...
...
...
...
...
...
SAE J1939 and J1708 is the vehicle bus standard used for communication and diagnostics among vehicle components. Based on the same architecture FMS protocol dedicated to telematics systems is available.
- SAE J1708 is a standard used for serial communications between ECUs on heavy duty.
The hardware utilized is RS-485 transceivers wired for open collector operation through the use of a pullup and pulldown of the separate data lines.
J1708 functionality is used to read vehicle's Fuel Level and Fuel consumption.
Because fuel CAN data J1708 is not a CAN-BUS protocol, FMB640 CAN1 and CAN2 lines cannot be used to read J1708 information. FMB640 has a special J1708 Port, which utilizes an RJ9 4P4C connector.
- FMS CAN data(J1939), or Fleet Management Systems Interface, is a sector to configure and manage events based on vehicle data of commercial vehicles. Vehicle data comes through CAN line.
The FMS standard defines a gateway between the J1939 vehicle network and a fleet management system.
FMS Standard lower layer protocols:
- Application layer – SAE J1939/71
- Data link layer – SAE J1939/21 (FMS data are coded according to SAE J1939)
- Physical layer – ISO 11898-2 High-speed CAN, 250 kbit/s bus speed
- Physical connectors – Not standardized
| time | version | common name | notes |
|---|---|---|---|
| 2002 | 1.0 | Truck FMS Standard | Initial release |
| 2007 | 00.01 | Bus FMS Standard | Specialized for buses and coaches including specific signals like door openings, etc. |
| 2010 | 02.00 | Truck FMS Standard | It took over some signals from the Bus FMS Standard, but still handled separately for Trucks. |
| 2012 | 03 | FMS Standard | Harmonized Bus and Truck standard (with separated sections inside for buses and trucks). |
| 2017 | 04 | FMS Standard | Harmonized Bus and Truck standard (with adding Cruise control states) |
direct J1708/J1939 connection
Teltonika FMB640 FMX640 offers the following options for direct J1708/J1939 connection:
- through the 2x10 socket (front side)
- SAE J1939, CAN 1, FMS
- SAE J1939, CAN 1, raw/manual (i.e. without FMS)
You get raw CAN data from the vehicle CAN lines. Please- configure required data filters on FMB640 and
- setup your server to correctly interpret the raw data received from FMB640.
- SAE J1939, CAN 2, FMS
- SAE J1939, CAN 2, raw/manual (i.e. without FMS)
You get raw CAN data from the vehicle CAN lines. Please- configure required data filters on FMB640 and
- setup your server to correctly interpret the raw data received from FMB640.
- through the J1708 socket (back side, RJ11 port)
- SAE J1708 (actually RS-485 at physical layer)
...
references
- FMB640 SMS/GPRS command list
- https://wiki.teltonika-gps.com/view/FMB640_LVCAN_I/O,FMS_IO_and_Tachograph_data_elements
- https://wiki.teltonika-gps.com/view/FMB640_Teltonika_Data_Sending_Parameters_ID#FMS_elements
- https://wiki.teltonika-gps.com/view/FMB640_J1708
- https://wiki.teltonika-gps.com/view/FMB641_CAN_%5C_Tachograph
...
FAQ
...
Q: Are SAE J1939 ports read only?
...
Q: Where do I get the SAE J1939 wiring diagram for a vehicle?
A: Please contact
support@mirifica EU us,
maybe we have the right SAE J1939 wiring diagram for the vehicle.
If not, you shall contact the vehicle manufacturer or one of its authorized service centers.
...
Q: How does the tcp link work in FMB640?
A: TCP link mode works like a "tunnel" connecting RS232 device with the server. FMB640 simply acts like a "data tunnel".
Using TCP link mode, each time RS232 message is received, FMB640 would re-sent RS232 data to the server. This requires that FMB640 is connected to the server 24/7 and always has open data link with the server, because TCP link mode only works when device has open data link with the server.
...
Q: Does FMB640 support modbus ?
A: FMB640, FM63 and FMB125 support RS485, can support MODBUS. But functionality is not available, thus special development is required.
...