desktop application
.... getDDD
WEB Tacho
ddd.teltonika.lt or IP: 212.59.13.226
company management > email address
https://wiki.teltonika.lt/view/WEB_Tacho_Company_Management
Email > Enter recipient's email address (Mandatory): you get notifications to this email address about your licenses (when expire date is coming) and about units (when you are closing to unit limit).
user management > email address
https://wiki.teltonika.lt/view/WEB_Tacho_User_management
Email > Enter user email address (Mandatory): you can configure in "user settings" for each user to receive e-mail messages for failed schedules and Receive e-mail messages with ddd files attached on schedule completion.
Note: When you face issue with DDD donwload, please write in advance that with older firmware, DDD download was successful if it was the case, Because it will be not possible to downgrade to older firmware due to stability improvements.
FAQ
Q: After installing Remote Smart Card reader software for 1.0.0 to 3.0.10, company card is no longer connected to the Tacho WEB?
R: Check firewall settings and make sure that PORTS: 29000-29003 are accessible from the inside of the network ( Also when working with Remote Smart Card reader software, it's better to ask for software logs, which are located: C:\Program Files (x86)\Teltonika\SCard Reader\Service\Logs)
Digital tachograph monitoring solution
There are two ways to implement software:
- You can use special Web Tacho application from Teltonika
https://ddd.teltonika.lt/Account/Login?ReturnUrl=%2f - Develop your own software.
In case you choose latter scenario, you will be provided with special communication protocol, which you will use when developing software solution. On the other hand, in case you choose Teltonika Web Tacho solution, you are ready to go.
- Devices with DDD download and tacho online functionality:
FM6300
FMB640
FMC640
FMM640
https://wiki.teltonika.lt/view/Digital_tachograph_monitoring_and_data_reports
Note
Tachograph files from VDO 4.0 are in "GEN2" format and cannot be opened by regular DDD reader (which only support GEN1 formats). So to open GEN2 files, you need to have GEN2 software.
One of the tachograph file viewer software, which support GEN2 files - https://www.tachosys.com/Downloads/Software --> Tachograph File Viewer 3.05
Connection and configuration of the tachograph for the FMB640
Teltonika Tachograph Solution is a big forward leap in remote tachograph data files download. Solution is easily manageable and does not require any complex software installation. Everything is accessible via web page. Now you can download tachograph files from any place and from any PC via internet access. Read more...https://wiki.teltonika.lt/view/FMB640_and_Tachograph_Solution
- Supported devices are:
Siemens VDO Digital Tachograph - DTCO 1381 (release 1.3a, 1.4 or later) and Stoneridge Tachograph - SE5000 (release 7.1 or later).
To use tachograph, devices must have:
- Tachograph live data (K-line) - data from digital tachograph
- Remote tachograph file download
- Teltonika Web Tacho application or other software to download files and monitor data
- FMS CAN Data (J1939)
FAQ
- When tachocheck respond with 000 that means: Either the vehicles Ignition must be either OFF or CAN2 wires are not connected to the tachograph (instructions for connection: https://wiki.teltonika.lt/view/FMB640_and_Tachograph_Solution)
Connection of the tachograph for the FM6320
C5+C7 connection is used for DDD files download
D8 K-Line used to monitor tachograph events.
These are parameters you can get from K-Line:
Drive recognize
Driver 1 working state
Driver 2 working state
Overspeed
Driver 1 card
Driver 2 card
Driver 1 time rel state
Driver 2 time rel state
Speed
Odometer
Distance of current journey
Timestamp
Driver 1 ID MSB
Driver 1 ID LSB
Driver 2 ID MSB
Driver 2 ID LSB
FAQ
Q: Which AVL-ID should I use to receive the "Tacho Data Source"?
A: AVL_ID for "Tacho Data Source" is AVLID=48
0 Comments